sma5j5.0a thru sma5j40ca www.vishay.com vishay general semiconductor revision: 24-oct-12 1 document number: 88875 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 high power density surface mount t rans z orb ? transient voltage suppressors devices for bi-direction applications for bi-directional devices use ca suffix (e.g. sma5j40ca). electrical characteristics apply in both directions. features ? low profile package ? ideal for automated placement ? glass passivated chip junction ? available in uni-directional and bi-directional ? excellent clamping capability ? very fast response time ? low incremental surge resistance ? meets msl level 1, per j-st d-020, lf maximum peak of 260 c ? aec-q101 qualified ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 typical applications use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial, automo tive, and telecommunication. mechanical data case: do-214ac (sma) ? molding compound meets ul 94 v-0 flammability rating base p/n-e3 - rohs compliant, commercial grade ? base p/nhe3 - rohs compliant, aec-q101 qualified terminals: matte tin plated leads, solderable per j-std-002 and jesd 22-b102 ? e3 suffix meets jesd 201 class 1a whisker test, he3 suffix meets jesd 201 class 2 whisker test polarity: for uni-directional types the band denotes cathode end, no marking on bi-directional types notes (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2. (2) mounted on 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads to each terminal primary characteristics v br 6.4 v to 49.1 v v wm 5.0 v to 40 v p ppm 500 w i fsm (uni-directional only) 40 a t j max. 150 c polarity uni-directional, bi-directional package do-214ac (smba) do-214ac ( s ma) maximum ratings (t a = 25 c unless otherwise noted) parameter symbol value unit peak pulse power di ssipation with a 10/1000 s waveform (1)(2) (fig. 1) p ppm 500 w peak pulse current with a 10/1000 s waveform (1) i ppm see next table a peak forward surge current 8.3 ms sing le half sine-wave uni-directional only (2) i fsm 40 a operating junction and storage temperature range t j , t stg - 55 to + 150 c
sma5j5.0a thru sma5j40ca www.vishay.com vishay general semiconductor revision: 24-oct-12 2 document number: 88875 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) pulse test: t p ? 50 ms (2) surge current waveform per fi g. 3 and derate per fig. 2 (3) for bi-directional types having v wm of 10 v and less, the i d limit is doubled (4) all terms and symbols are cons istent with ansi/ieee c62.35 (5) for the bi-directional sma5j5.0ca, the maximum v br is 7.25 v (6) v f = 3.5 v at i f = 25 a (uni-dir ectional only) note (1) mounted on minimum recommended pad layout note (1) aec-q101 qualified electrical characteristics (t a = 25 c unless otherwise noted) device type device marking code breakdown voltage v br (v) (1) test current i t (ma) stand-off voltage v wm (v) maximum reverse leakage at v wm i d (a) (3) maximum peak pulse surge current i ppm (a) (2) maximum clamping voltage at i ppm v c (v) uni bi min. max. sma5j5.0a (5) 5ae 5ae 6.40 7.07 10 5.0 800 54.3 9.2 sma5j6.0a 5ag 5ag 6.67 7.37 10 6.0 800 48.5 10.3 sma5j6.5a 5ak 5ak 7.22 7.98 10 6.5 500 44.6 11.2 sma5j7.0a 5am 5am 7.78 8.60 10 7.0 200 41.7 12.0 sma5j7.5a 5ap 5ap 8.33 9.21 1.0 7.5 100 38.8 12.9 sma5j8.0a 5ar 5ar 8.89 9.83 1.0 8.0 50 36.8 13.6 sma5j8.5a 5at 5at 9.44 10.4 1.0 8.5 10 34.7 14.4 sma5j9.0a 5av 5av 10.0 11.1 1.0 9.0 5.0 32.5 15.4 sma5j10a 5ax 5ax 11.1 12.3 1.0 10 1.0 29.4 17.0 sma5j11a 5az 5az 12.2 13.5 1.0 11 1.0 27.5 18.2 sma5j12a 5be 5be 13.3 14.7 1.0 12 1.0 25.1 19.9 sma5j13a 5bg 5bg 14.4 15.9 1.0 13 1.0 23.3 21.5 sma5j14a 5bk 5bk 15.6 17.2 1.0 14 1.0 21.6 23.2 SMA5J15A 5bm 5bm 16.7 18.5 1.0 15 1.0 20.5 24.4 sma5j16a 5bp 5bp 17.8 19.7 1.0 16 1.0 19.2 26.0 sma5j17a 5br 5br 18.9 20.9 1.0 17 1.0 18.1 27.6 sma5j18a 5bt 5bt 20.0 22.1 1.0 18 1.0 17.1 29.2 sma5j20a 5bv 5bv 22.2 24.5 1.0 20 1.0 15.4 32.4 sma5j22a 5bx 5bx 24.4 26.9 1.0 22 1.0 14.1 35.5 sma5j24a 5bz 5bz 26.7 29.5 1.0 24 1.0 12.9 38.9 sma5j26a 5ce 5ce 28.9 31.9 1.0 26 1.0 11.9 42.1 sma5j28a 5cg 5cg 31.1 34.4 1.0 28 1.0 11.0 45.4 sma5j30a 5ck 5ck 33.3 36.8 1.0 30 1.0 10.3 48.4 sma5j33a 5cm 5cm 36.7 40.6 1.0 33 1.0 9.4 53.3 sma5j36a 5cp 5cp 40.0 44.2 1.0 36 1.0 8.6 58.1 sma5j40a 5cr 5cr 44.4 49.1 1.0 40 1.0 7.8 64.5 thermal characteristics (t a = 25 c unless otherwise noted) parameter symbol value unit typical thermal resistance , junction to ambient (1) r ? ja 80 c/ w typical thermal resistance, junction to lead r ? jl 25 ordering information (example) preferred p/n unit weight (g) preferred pa ckage code base quantity delivery mode sma5j5.0a-e3/61 0.064 61 1800 7" di ameter plastic tape and reel sma5j5.0a-e3/5a 0.064 5a 7500 13" di ameter plastic tape and reel sma5j5.0ahe3/61 (1) 0.064 61 1800 7" diameter plastic tape and reel sma5j5.0ahe3/5a (1) 0.064 5a 7500 13" diameter plastic tape and reel
sma5j5.0a thru sma5j40ca www.vishay.com vishay general semiconductor revision: 24-oct-12 3 document number: 88875 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ratings and characteristics curves (t a = 25 c unless otherwise noted) fig. 1 - peak pulse power rating curve fig. 2 - pulse power or current vs. initial junction temperature fig. 3 - pulse waveform fig. 4 - typical junction capacitance fig. 5 - typical transient thermal impedance fig. 6 - maximum non-repetitive peak forward surge current uni-directional use only 0.1 1 10 100 n on-repetiti v e p u lse w a v eform sho w n in fig. 3 t a = 25 c p ppm - peak p u lse po w er (k w ) t d - p u lse w idth (s) 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms 0 255075100 100 75 50 25 0 125 150 175 200 t j - initial temperat u re (c) peak p u lse po w er (p pp ) or c u rrent (i pp ) derating in percentage, % 0 50 100 150 t d 0 1.0 2.0 3.0 4.0 i ppm - peak p u lse c u rrent, % i rsm t - time (ms) t r = 10 s peak val u e i ppm half val u e - i ppm i pp 2 10/1000 s w a v eform as defined by r.e.a. t j = 25 c p u lse w idth (t d ) is defined as the point w here the peak c u rrent decays to 50 % of i ppm uni-directional bi-directional 10 100 1000 10 000 10 1 100 200 meas u red at zero bias meas u red at stand-off voltage v w m t j = 25 c f = 1.0 mhz c j - j u nction capacitance (pf) v w m - re v erse stand-off voltage (v) 1 10 100 0.01 0.1 10 1 100 1000 t p - p u lse d u ration (s) transient thermal impedance (c/ w ) 50 10 5 1 100 10 50 100 200 t j = t j max. 8.3 ms single half sine- w a v e nu mber of cycles at 60 hz peak for w ard s u rge c u rrent (a)
sma5j5.0a thru sma5j40ca www.vishay.com vishay general semiconductor revision: 24-oct-12 4 document number: 88875 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package outline dimensions in inches (millimeters) 0.008 (0.203) 0.194 (4.93) 0.208 (5.28) 0.157 (3.99) 0.177 (4.50) 0.100 (2.54) 0.110 (2.79) 0.078 (1.98) 0.090 (2.29) 0.006 (0.152) 0.012 (0.305) 0.049 (1.25) 0.065 (1.65) cathode band 0 (0) do-214ac ( s ma) mountin g pad layout 0.074 (1.88) max. 0.208 (5.28) ref. 0.066 (1.68) min. 0.060 (1.52) min. 0.030 (0.76) 0.060 (1.52)
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
